cmake/macros.cmake
author Sam Lantinga <slouken@libsdl.org>
Sat, 27 Jul 2013 03:20:09 -0700
changeset 7526 6c0f0280149c
parent 7182 1089a8a701c3
child 9465 bf1da29c9509
permissions -rw-r--r--
Fixed bug 1272 - Bogus numlock key up/down events being reported on MacOS X Vern Jensen The problem is that in certain situations I'm getting THREE keyUp/keyDown events when I push certain keys. In my event code I added: case SDL_KEYUP: printf("SDL KeyScanCode for KEYUP event: %d\n", event->key.keysym.scancode ); … and case SDL_KEYDOWN: printf("SDL KeyScanCode for KEYDOWN event: %d\n", event->key.keysym.scancode ); … The result of one test run where I push 2 keys and then release them is this: SDL KeyScanCode for KEYDOWN event: 92 // Pushed keypad 4 SDL KeyScanCode for KEYDOWN event: 83 // Pushed left shift SDL KeyScanCode for KEYUP event: 83 SDL KeyScanCode for KEYDOWN event: 225 SDL KeyScanCode for KEYUP event: 92 // Released keypad 4 SDL KeyScanCode for KEYDOWN event: 83 SDL KeyScanCode for KEYUP event: 83 SDL KeyScanCode for KEYUP event: 225 // Released left shift There *should* be only a total of 4 events above… 2 for each key being pushed, and 2 for each being released. But instead some bogus events for numlock being pushed/released are sent from SDL. These events did not occur. I did not push numlock. The value above for numlock is 83. Comments above show when I pushed each key. As you can see, when I push left shift, THREE events are instantly sent to my application, keyDown and then keyUp for numlock, and then the valid event for left shift (the key that was actually pushed). You could replace keypad 4 with pretty much any keyPad key and it'll still happen. You can also replace it with any arrow key and it'll happen. However, when trying it with normal letter keys on the main keyboard it didn't. It happens with other modifier keys too, not just left shift. The order in which the keys are pressed matter. For instance, if I do: 1) keypad 4 2) left shift 3) release left shift 4) release keypad 4 Then at step 2, I get the 3 events above (when there should be only one), but steps 3 and 4 work properly… I don't get extra keyUp/keyDown events for steps 3 or 4. Thereas if the order of steps 3 and 4 are reversed, I get the bogus extra events for numlock. Also, the problem can occur even when pushing just a single key by itself. If I push left shift, then keypad 4, then release left shift, then release keypad 4, then the following push of left shift will cause the bug. If I continue pushing and releasing left shift though, it won't happen again until I again involve keypad keys. --- Sam Lantinga According to the Apple documentation, NSNumericPadKeyMask is set for any arrow or numeric keypad event. Indeed this is what's happening. I verified that we get the correct events for the numlock key and the mod state gets set correcly, so it should be safe to remove this bogus code.

macro(SET_OPTION _NAME _DESC)
  list(APPEND ALLOPTIONS ${_NAME})
  if(${ARGC} EQUAL 3)
    set(_DEFLT ${ARGV2})
  else()
    set(_DEFLT OFF)
  endif()
  option(${_NAME} ${_DESC} ${_DEFLT})
endmacro()

macro(DEP_OPTION _NAME _DESC _DEFLT _DEPTEST _FAILDFLT)
  list(APPEND ALLOPTIONS ${_NAME})
  cmake_dependent_option(${_NAME} ${_DESC} ${_DEFLT} ${_DEPTEST} ${_FAILDFLT})
endmacro()

macro(OPTION_STRING _NAME _DESC _VALUE)
  list(APPEND ALLOPTIONS ${_NAME})
  set(${_NAME} ${_VALUE} CACHE STRING "${_DESC}")
  set(HAVE_${_NAME} ${_VALUE})
ENDMACRO()

# Message Output
macro(MESSAGE_WARN _TEXT)
  message(STATUS "*** WARNING: ${_TEXT}")
endmacro()

macro(MESSAGE_ERROR _TEXT)
  message(FATAL_ERROR "*** ERROR: ${_TEXT}")
endmacro()

macro(MESSAGE_BOOL_OPTION _NAME _VALUE)
  if(${_VALUE})
    message(STATUS "  ${_NAME}:\tON")
  else()
    message(STATUS "  ${_NAME}:\tOFF")
  endif()
endmacro()

macro(MESSAGE_TESTED_OPTION _NAME)
  set(_REQVALUE ${${_NAME}})
  set(_PAD " ")
  if(${ARGC} EQUAL 2)
    set(_PAD ${ARGV1})
  endif()
  if(NOT HAVE_${_NAME})
    set(HAVE_${_NAME} OFF)
  elseif("${HAVE_${_NAME}}" MATCHES "1|TRUE|YES|Y")
    set(HAVE_${_NAME} ON)
  endif()
  message(STATUS "  ${_NAME}${_PAD}(Wanted: ${_REQVALUE}): ${HAVE_${_NAME}}")
endmacro()

macro(LISTTOSTR _LIST _OUTPUT)
  if(${ARGC} EQUAL 3)
    # prefix for each element
    set(_LPREFIX ${ARGV2})
  else()
    set(_LPREFIX "")
  endif()
  # Do not use string(REPLACE ";" " ") here to avoid messing up list
  # entries
  foreach(_ITEM ${${_LIST}})
    set(${_OUTPUT} "${_LPREFIX}${_ITEM} ${${_OUTPUT}}")
  endforeach()
endmacro()

macro(CHECK_OBJC_SOURCE_COMPILES SOURCE VAR)
  set(PREV_REQUIRED_DEFS "${CMAKE_REQUIRED_DEFINITIONS}")
  set(CMAKE_REQUIRED_DEFINITIONS "-ObjC ${PREV_REQUIRED_DEFS}")
  CHECK_C_SOURCE_COMPILES(${SOURCE} ${VAR})
  set(CMAKE_REQUIRED_DEFINITIONS "${PREV_REQUIRED_DEFS}")
endmacro()